LaCie 2Big Network
Aus NAS Wiki
Inhaltsverzeichnis |
Technische Daten
| Type | |
|---|---|
| CPU | Marvell Orion 400 MHz ARM9E |
| Memory | 64 MB |
| Datenübertragung | 10/100/1000Mbit/s |
| Schnittstelle | SATA |
| Anschlüsse | 2x USB, Ethernet |
| Festplatten | 2 x 3,5" mit 2x500, 2x1000, 2x1500 oder 2x2000 GB |
| Stromverbrauch | ? |
| Festplatten-Modus | RAID 0, RAID 1 |
| File Sharing | SMB, AFP, HTTP, FTP (Unterstützung von Zeroconf) |
Bilder
Datei:2BIG front.jpg Frontseite |
Datei:2BIG.jpg Rückseite |
Übersicht
Das LaCie 2Big NAS gibt es nur vorbestückt mit Festplatten unterschiedlicher Kapazität. In diesem Exemplar sind zwei 1 TB Festplatten von Seagate Barracuda 7200.11 ST31000333AS verbaut. Das NAS Betriebssystem ist direkt auf den Festplatten installiert.
Aufbau
Technische Details
Die Ausgabe von cat /proc/cpuinfo
Processor : ARM926EJ-Sid(wb) rev 0 (v5l) BogoMIPS : 266.24 Features : swp half thumb fastmult CPU implementer : 0x41 CPU architecture: 5TEJ CPU variant : 0x0 CPU part : 0x926 CPU revision : 0 Cache type : write-back Cache clean : cp15 c7 ops Cache lockdown : format C Cache format : Harvard I size : 32768 I assoc : 1 I line length : 32 I sets : 1024 D size : 32768 D assoc : 1 D line length : 32 D sets : 1024 Hardware : MV-88fxx81 Revision : 0000 Serial : 0000000000000000
Ausgabe von dmesg:
Linux version 2.6.12.6-arm1-lacie5e (root@lacie) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #29 Fri Aug 10 11:08:36 CEST 2007 CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 200000000, Tclk = 166666667 Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 16384 DMA zone: 16384 pages, LIFO batch:7 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro reset=0 PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 64MB 0MB 0MB 0MB = 64MB total Memory: 60928KB available (2786K code, 411K data, 648K init) Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 64MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e0000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base e8000000, size 128MB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....no such DEVICE_CS1 ....base f4000000, size 16MB DEVICE_CS2 ....no such DEV_BOOCS ....base ff800000, size 8MB CRYPTO ENG ....base f0000000, size 64KB LaCie EDmini V2 (MV LSP Version 1.10.3.patch2_DB_NAS)-- RD-88F5182-EDMV2 Soc: 88F5182 A2 Detected Tclk 166666667 and SysClk 200000000 Marvell USB EHCI Host controller #0: c04efb00 Marvell USB EHCI Host controller #1: c04efa40 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub Use the XOR engines (offloading) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero o copy user to/from kernel buffers Number of XOR engines to use: 2 Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 Registering unionfs 1.1.5 Initializing Cryptographic API Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface 'egiga0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter Vendor: Seagate Model: ST31000333AS Rev: LC15 Type: Direct-Access ANSI SCSI revision: 03 Vendor: Seagate Model: ST31000333AS Rev: LC15 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sda: drive cache: write back SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sda: drive cache: write back sda: sda1 < sda5 sda6 sda7 sda8 sda9 sda10 > sda2 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sdb: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sdb: drive cache: write back sdb: sdb1 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > sdb2 Attached scsi disk sdb at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0 Attached scsi generic sg1 at scsi0, channel 0, id 0, lun 0, type 0 physmap flash device: 80000 at ff800000 phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 phys_mapped_flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available ehci_platform ehci_platform.4523: EHCI Host Controller ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523: park 0 ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_platform ehci_platform.16781: EHCI Host Controller ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2 ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781: park 0 ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice edmini_power 1.0 initialised i2c /dev entries driver md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 5 Loading I2C based RTC driver device interface. Found TWSI adapter with id: 0 Found I2C RTC rs5c372 @ 0x32 Freeing init memory: 648K md: md0 stopped. md: bind<sda7> raid1: raid set md0 active with 1 out of 2 mirrors EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. EXT3-fs: recovery complete. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. md: bind<sdb7> RAID1 conf printout: --- wd:1 rd:2 disk 0, wo:0, o:1, dev:sda7 disk 1, wo:1, o:1, dev:sdb7 .<6>md: syncing RAID array md0 md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. md: using maximum available idle IO bandwith (but not more than 200000 KB/sec) for reconstruction. md: using 128k window, over a total of 7936 blocks. md: md0: sync done. RAID1 conf printout: --- wd:2 rd:2 disk 0, wo:0, o:1, dev:sda7 disk 1, wo:0, o:1, dev:sdb7 md: md1 stopped. md: bind<sdb8> md: bind<sda8> raid1: raid set md1 active with 2 out of 2 mirrors md: mdadm(pid 422) used obsolete MD ioctl, upgrade your software to use new ictls. md: md2 stopped. md: bind<sdb9> md: bind<sda9> raid1: raid set md2 active with 2 out of 2 mirrors md: mdadm(pid 481) used obsolete MD ioctl, upgrade your software to use new ictls. md: md3 stopped. md: bind<sdb5> md: bind<sda5> raid1: raid set md3 active with 2 out of 2 mirrors md: mdadm(pid 540) used obsolete MD ioctl, upgrade your software to use new ictls. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. EXT3-fs: recovery complete. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on md2, internal journal EXT3-fs: mounted filesystem with ordered data mode. SGI XFS with ACLs, security attributes, no debug enabled SGI XFS Quota Management subsystem NTFS driver 2.1.22 [Flags: R/O MODULE]. Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. Adding 128376k swap on /dev/md3. Priority:-1 extents:1 egiga0: link down md: md4 stopped. md: bind<sdb2> md: bind<sda2> raid1: raid set md4 active with 2 out of 2 mirrors md: mdadm(pid 1082) used obsolete MD ioctl, upgrade your software to use new ictls. XFS mounting filesystem md4 Ending clean XFS mount for filesystem: md4 egiga0: link up<5>, full duplex<5>, speed 1 Gbps<5> egiga0: link down egiga0: change mtu 1500 (buffer-size 1520) to 9004 (buffer-size 9024) egiga0: link up<5>, full duplex<5>, speed 1 Gbps<5> md: mdadm(pid 1375) used obsolete MD ioctl, upgrade your software to use new ictls. md: mdadm(pid 1468) used obsolete MD ioctl, upgrade your software to use new ictls. md: mdadm(pid 1467) used obsolete MD ioctl, upgrade your software to use new ictls.
Partitionierung
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 125 1004031 5 Extended /dev/sda2 126 121601 975755970 83 Linux /dev/sda5 1 16 128457 82 Linux swap /dev/sda6 17 17 8001 83 Linux /dev/sda7 18 18 8001 83 Linux /dev/sda8 19 40 176683+ 83 Linux /dev/sda9 41 124 674698+ 83 Linux /dev/sda10 125 125 8001 83 Linux
